Spring Sale Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: pass65
marks4sure logo
You have configured your Brocade device as shown in the exhibit.
Brocade#sh ip
Switch IP address: 10.200.128.116
Subnet mask: 255.255.255.0
Default router address: 10.200.128.1
TFTP server address: 10.200.46.57
Configuration filename: Brocade
Image filename: None
IP MTU: 1500
Brocade#traceroute 10.200.128.1
Type Control-c to abort
Tracing the route to IP node 10.200.128.1 from 1 to 30 hops
1 < 1 ms < 1 ms < 1 ms 10.200.128.1
Which statement is correct regarding interface Ethernet 10 on this device having inbound traffic from 172.17.1.1/24 to 172.17.2.1/24 on port 21?
Which two features are implemented using Brocade IronStack technology? (Choose two.)
You want to classify and mark traffic at the edge of your network before it is sent to the core and routed where Layer 3 QoS is trusted and enabled. Which type of marking should you configure to ensure your application traffic is serviced correctly in the core of your network?
You have been informed a group of remote employees are unable to authenticate with the RADIUS server. From the Brocade FCX router, you enable the debug dot1x events command.
Which three events will be viewed? (Choose three.)
Which two access control list (ACL) types will match on TCP/UDP ports? (Choose two.)
Which type of transceiver would be used to support a 5 km single mode fiber 10 Gbps connection?
Which two destination addresses are used in an ARP request if the source station's IP address is:
192.168.5.12/16? (Choose two.)
Two sites 8 km apart will be connected together using fiber optic cable. Which SFP/cable combination needs to be used?
You are implementing an OSPF network with five defined areas. You want to configure OSPF area route sharing to other specified OSPF areas.
Which router will you need to configure to share area routes with other area routes?
You need to expedite a case to Brocade support for troubleshooting. What information is needed? (Choose three.)
Which QoS mechanism would you use to set the DSCP value specified of an outgoing packet?
Which two protocols would be used to transfer new code to a Brocade FastIron, TurboIron, or NetIron device? (Choose two.)
An identical route has been discovered by OSPF and RIP. By default, the OSPF route is chosen and added to the routing table. What should be done to allow the RIP route to be preferred?
OU need to improve redundancy in your LAN as well as increase bandwidth between switches using a Layer 2 protocol.
Which feature will provide this?
On Brocade FastIron, TurboIron, and NetIron platforms, which command saves the running configuration to the flash's startup configuration?
Which type of message is exchanged between switches to prevent loops and maintain loop-free topologies?
Which two statements are true about QoS when implemented on a Brocade FastIron platform? (Choose two.)
In the exhibit, the network is running Spanning Tree 802.ID. Which port will be placed in a blocked state?
When configuring an IP static route in a Brocade router, which three parameters are required?
(Choose three.)
Which three transceiver form factors are supported by Brocade switches and routers? (Choose three.)
What does the command copy flash tftp 192.168.13.37 FGSR07001.bin secondary do?
Optical monitoring is not returning data. What are three reasons for this happening? (Choose three.)
Given the command output shown below:
de(config)#mirror-port ethernet 1/2/4
Brocade(config)#interface ethernet 1/2/11
Brocade(config-if-e100-11)#monitor ethernet 1/2/4 both
What do the Brocade commands accomplish?
TESTED 02 May 2026