Spring Sale Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: pass65
marks4sure logo
The service-mtu of a VPLS using MPLS encapsulation is set to 9100. What is the minimum MTU value that can be set for the network port if fast re-route facility mode is used on the SDP LSP?
After the " disable-learning " command has been executed at the VPLS level, a new client device originates a frame. What is the result?
The service mtu of a VPLS is set to 9100. What is the recommended MTU value that can be set for the access port assuming dot1q encapsulation?
An l-VPLS is configured with a service id of 511. What will the value of the l-SID be assuming a default configuration?
Click on the exhibit below.
Based on the following configuration which VLANs will be managed by the management VPLS?
What action will be taken when an Ethernet switch receives a frame with a known DA and an outer Ethertype value of 0x0800 on a dot1q encapsulated port?
Which of the following are true when ports are configured with the IEEE 802.3ah Loopback Control feature? (Choose 3)
Which of the following must be true in order to add a port to a LAG? (Choose 2)
Click on the exhibit below.
In the diagram below, SAP 1 is put into the blocking state as a result of the spanning tree protocol. What will occur in the VPLS instance if SAP 2 goes down and SAP 1 transitions to the forwarding state? Select the most accurate statement.
Click on the exhibit below.
Based on the service-mtu of this B-VPLS, what is the maximum service-mtu of any connecting I-VPLS attached to this B-VPLS?
Click on the exhibit below.
A new router named PE-D is to be directly connected to PE-C and is required to be added to the existing VPLS 300. The design requires the least amount of signaling, the least amount of configuration changes for existing sites and the new site has to have access to all existing sites. How should the new site be added to VPLS 300?
When spanning tree is enabled within a VPLS service and the STP mode is 802.1 D 2004 what happens if a PVST BPDU is received on a SAP?
If a management VPLS is administratively disabled what will be the status of the associated user VPLS SAPs?
IEEE 802.3ah is similar to SONET/SDH in that it can count and report bit errors and frame errors.
Fill in the blank for this next sentence. Flooded traffic received on any ____________ in the service is replicated to other spoke SDPs and SAPs and not transmitted on any mesh SDPs.
During the process of troubleshooting a VPLS problem the " oam mac-purge " command with " register " option was used to purge a MAC address from the FDB. Which of the following statements is true?
How can one ensure that a specific switch will be select as root in an STP network?
Which protocol is used to signal the status of the active links between the PE and the CE in MC-LAG?
What scaling factors should a network engineer be aware of when designing VPLS networks? (Choose 3)
Click on the exhibit below.
How many LSPs are required in total between Metro A and Metro B if 100 hierarchical VPLS services are deployed across the two metro networks?
Click on the exhibit below.
The MDU attached to this PE has been configured with active/standby SDP ' s configuration option has been configured for the PE to recognize that this SDP is in standby mode?
Assuming TLDP and RSVP are both being used in an MPLS network core which of the following statements is true?
Why is MAC explosion a factor to be considered when designing a large VPLS network? (Choose 2)
Which of the following is a function of the data plane that must be considered when provisioning a VPLS service?
Click on the exhibit below.
Given the following configuration, which service type will VPLS 1 and VPLS 100 be displayed as with the " show service service-using " command?
Click on the exhibit below.
You have been requested to add load balancing across the redundant spoke-SDPs in the network shown. What further configuration is required? (Choose 2)
Why should you configure send-flush-on failure on your PE routers when using active/standby pseudowires?
The command " send flush-on-failure " has been enabled within a VPLS instance. What does the PE do upon detection of a SAP failure within the VPLS?
What is the MTU impact on the SDP path-mtu if fast reroute, one-to-one mode is implemented on the LSP?
Click on the exhibit below.
The SAP on PE-A has been configured with dot1q encapsulation. The SAP on PE-B has been configured with qinq encapsulation. CE-A sends frames with a single tag of 100. The VLAN tag from CE-A must be passed transparently. CE-B is expecting a frame with a top tag of 200 and bottom tag of 100. Which of the following is the correct SAP id for PE-B?
TESTED 01 May 2026
